Skip to content

About

Bang & Olufsen Beo4 remote for Flipper Zero: 455 kHz IR straight from the timer

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Latest commit

 

History

2 Commits

Folders and files

Repository files navigation

Beo4 for Flipper Zero

A Flipper Zero app that works as a Bang & Olufsen Beo4 remote.

Beo4 app on Flipper Zero

B&O gear listens on a 455 kHz IR carrier. The stock Infrared app on Flipper only transmits 10–56 kHz, so it cannot talk to B&O at all. This app drives the IR LED itself: the IR pin (PB9) is the TIM1_CH3N output, the timer runs a 457 kHz PWM (64 MHz / 140), and each 200 µs flash is opened and closed by switching the channel's output mode. No extra hardware is needed.

Tested

On a BeoSound Ouverture system with BeoLab 2000 speakers in Master Link link rooms, Flipper firmware Momentum mntm-009:

Key Address / command Result
Vinyl / wave (PHONO) 0x01 / 0x93 ✅ switches the Ouverture to its AUX input
RADIO 0x01 / 0x81 ✅
CD 0x01 / 0x92 ✅
Volume + / − 0x01 / 0x60, 0x01 / 0x64 ✅

PHONO also works when aimed at a BeoLab 2000 in a link room: it starts the main room's source there.

On the Ouverture the AUX input answers to PHONO, not to A.AUX (0x01 / 0x83) or V.AUX (0x01 / 0x82).

Not tested yet: A.TAPE, GO, STOP, Standby, ALL off (0x0F / 0x0C). Reports welcome.

Build and install

With ufbt and the SDK of your firmware:

ufbt          # builds dist/beo4_remote.fap
ufbt launch   # installs to the Flipper over USB and starts it

Or copy beo4_remote.fap from Releases to SD/apps/Infrared/. The release build is for Momentum mntm-009 (API 79.2); for other firmware build it yourself.

The app takes TIM1 directly. If the timer is busy (another IR app is running), it blinks red and exits.

Protocol

A Beo4 frame is a series of 200 µs flashes; the value is the gap to the next flash: 3125 µs = 0, 6250 µs = same as previous bit, 9375 µs = 1, 12500 µs = stop, 15625 µs = start. Order: 0, 0, start, link bit, 8-bit address, 8-bit command (MSB first), stop, final flash.

Sources:

По-русски

Пульт Beo4 для техники Bang & Olufsen на Флиппере. У B&O несущая 455 кГц, а штатное приложение «Инфракрасный порт» умеет только 10–56 кГц, поэтому светодиодом управляем напрямую через таймер TIM1. Проверено на BeoSound Ouverture: PHONO (вход AUX), RADIO и CD переключают источник, громкость ± работает; PHONO, направленный на BeoLab 2000 в комнате-ссылке, включает там звук главной комнаты по Master Link. Остальные кнопки пока не проверены.

License

MIT

About

Bang & Olufsen Beo4 remote for Flipper Zero: 455 kHz IR straight from the timer

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages